Corrigendum Renovation Exte, KURSEONG - Tender Details

• Opening Date : Sat 28th September, 2024
• Closing Date : Wed 25th September, 2024

• ₹ 1989474.00
• NTID 37443243

Corrigendum : Renovation, Extension And Supply Of Office Furnitures At Gram Panchayat Building, Ghayabari - Iii, Gp Under Kurseong Block. - "earth Work In Excavation Of Foundation Trenches Or Drains, In All Sorts Of Soil (including Mixed Soil But Excluding Laterite Or Sandstone) Including Removing, Spreading Or Stacking The Spoils Within A Lead Of 75 M. As Directed. The Item Includes Necessary Trimming The Sides Of Trenches, Levelling, Dressing And Ramming The Bottom, Bailing Out Water As Required Complete.(a) Depth Of Excavation Not Exceeding 1,500 Mm.", "earth Work In Filling In Foundation Trenches Or Plinth With Good Earth, In Layers Not Exceeding 150 Mm. Including Watering And Ramming Etc. Layer By Layer Complete. (payment To Be Made On The Basis Of Measurement Of Finished Quantity Of Work)(a) With Earth Obtained From Excavation Of Foundation.", Single Brick Flat Soling Of Picked Jhama Bricks Including Ramming And Dressing Bed To Proper Level And Filling Joints With Local Sand., "plum Concrete Work With 40 % Cement Concrete With 30 Mm Down Graded Stone Metal And 60 % Stone Boulder Of Size 150 Mm And Above, Placed In Position As Directed Excluding Shuttering If Any.(i) (1:3:6) Proportion", "(ii) Cement Concrete With 30 Mm Down Graded Shingles Excluding Shuttering.n.b. Varietyin Ground Floor(a) 1:3:6 Proportion", "ordinary Cement Concrete (mix 1:1.5:3) With Graded Stone Chips (20 Mm Nominal Size) Excluding Shuttering And Reinforcement If Any, In Ground Floor As Per Relevant Is Codes.(ii ) River Bazree", "reinforcement For Reinforced Concrete Work In All Sorts Of Structures Including Distribution Bars, Stirrups, Binders Etc Initial Straightening And Removal Of Loose Rust (if Necessary), Cutting To Requisite Length, Hooking And Bending To Correct Shape, Placing In Proper Position And Binding With 16 Gauge Black Annealed Wire At Every Intersection, Complete As Per Drawingand Direction.(a) For Works In Foundation And Upto Roof Of Ground Floor/upto 4 M(i) Tor Steel/mild Steeli. Sail/ Tata/rinl", "hire And Labour Charges For Shuttering With Centering And Necessary Staging Upto 4 M Using Approved Stout Props And Thick Hard Wood Planks Of Approved Thickness With Required Bracing For Concrete Slabs, Beams And Columns, Lintels Curved Or Straight Including Fitting, Fixing And Striking Out After Completion Of Works (upto Roof Of Ground Floor)(when The Height Of A Particular Floor Is More Than 4 M The Equivalent Floor Height Shall Be Taken As 4 M And Extra For Works Beyond The Initial 4 M Ht. Shall Be Allowed Under 12 (e) For Every 4 M Or Part Thereof)(a) 25 Mm To 30 Mm Thick Wooden Shuttering As Per Decision & Direction Of Engineer-in-charge.", "wood Work In Door And Window Frame Fitted And Fixed In Position Complete Including A Protective Coat Of Painting At The Contact Surface Of The Frame Exluding Cost Of Concrete, Iron Butt Hinges And M.s Clamps. (the Quantum Should Be Correted Upto Three Decimals).(d) Sal : Local", "panel Shutters Of Door And Window, As Per Design (each Panel Consisting Of Single Plank Without Joint), Including Fitting And Fixing The Same In Position But Excluding The Cost Of Hinge And Other Fittings.in Ground Floor.(in Case Of Non-supply Of Single Plank, Penal Rate Of Reduction Of 20% Will Be Made)(iii) 35mm Thick Shutters With 19mm Thick Panel Of Size 30 To 45 Cm.(b) Sishu, Gamar, Champ,badam,bhola, Mogra, Hallak.", "supplying, Fitting And Fixing Windows And Ventilators With Or Without Integrated Grills Conforming To Is 1038-1975 And Manufactured From Rolled Steel Sections Conforming To Is 7452-1974 With Non-friction Projecting Type, Box Type Hinges, Glazing Clips, Lugs Locking Bracket, Handle Plate Etc, Including Hoisting In Position, Straightening If Required, Fixing Lugs In Cement Concrete ( 1:2:4) With Stone Chips 20 Mm Down Cutting Holes And Mending Good Damages To Match With Existing Surface Complete In All Respect Excluding Glazing.(add Extra @ 1.2 % For Each Additional Floors Upto 4th Floor And @ 1.5% For Each Addl. Floor Above 4th Floor.)in Ground Floorflash Butt Welded Windows And Ventilators(no Shop Priming Will Be Allowed To Facilitate Inspection Of Workmanship)without Integrated Grills.(b) Openable Steel Windows As Per Is Sizes With Side Hung Shutters And Horizotal Glazing Bars. [the Extra Rate Admissible For The Openable Portion Only]", "supplying Best Indian Sheet Glass Panes Set In Putty And Fitted And Fixed With Nails And Putty Complete. (in All Floors For Internal Wall & Upto 6 M Height For External Wall)(i) 3 Mm Thick (weighing 7.4 Kg/sq.m)", 125 Mm. Thick Brick Work With 1st Class Bricks In Cement Mortar (1:4) In Ground Floor., "plaster (to Wall, Floor, Ceiling Etc.) With Sand And Cement Mortar Including Rounding Off Or Chamfering Corners As Directed And Raking Out Joints Including Throating, Nosing And Drip Course, Scaffolding/staging Where Necessary (ground Floor).[excluding Cost Of Chipping Over Concrete Surface](ii) With 1:4 Cement Mortar(a) 20 Mm Thick Plaster", "supplying, Fitting And Fixing M.s. Clamps For Door And Window Frame Made Of Flat Bent Bar, End Bifurcated With Necessary Screws Etc. By Cement Concrete(1:2:4) As Per Direction. (cost Of Concrete Will Be Paid Separately)(b) 40mm X 6mm, 200mm Length", "iron Butt Hinges Of Approved Quality Fitted And Fixed With Steel Screws, With Isi Mark.(vi) 100mm. X 50mm. X 1.25mm.", "anodised Aluminium Barrel / Tower / Socket Bolt (full Covered) Of Approved Manufactured From Extruded Section Conforming To I.s. 204/74 Fitted And Fixed With Cadmium Plated Screws:(vii) 225mm Long X 10mm Dia. Bolt.", "anodised Aluminium Skeleton Bolt Of Approved Quality Manufactured From Extruded Section Conforming To I.s: Specification (i.s: 204/74) Fitted And Fixed With Cadmiim Plated Screws:(vi) 450mm Long X 12mm Dia. Bolt.", "(a) M.s.or W.i. Ornamental Grill Of Approved Design Joints Continuously Welded With M.s, W.i. Flats And Bars Of Windows, Railing Etc. Fitted And Fixed With Necessary Screws And Lugs In Ground Floor.(add Extra @ 1% For Each Addl. Floor Upto 4th Floor And @ 1.25% For Each Addl. Floor Above 4th Floor)(i) Grill Weighing Above 10 Kg./sq.mtr And Up To 16 Kg./sq. Mtr.", (b) Priming One Coat On Timber Or Plastered Surface With Synthetic Oil Bound Primer Of Approved Quality Including Smoothening Surfaces By Sand Papering Etc., (a) Priming One Coat On Steel Or Other Metal Surface With Synthetic Oil Bound Primer Of Approved Quality Including Smoothening Surfaces By Sand Papering Etc., "(a) Painting With Best Quality Synthetic Enamel Paint Of Approved Make And Brand Including Smoothening Surface By Sand Papering Etc. Including Using Of Approved Putty Etc. On The Surface, If Necessary :(a) On Timber Or Plastered Surface :with Super Gloss (hi-gloss) -(iv) Two Coats (with Any Shade Except White)", "(a) Painting With Best Quality Synthetic Enamel Paint Of Approved Make And Brand Including Smoothening Surface By Sand Papering Etc. Including Using Of Approved Putty Etc. On The Surface, If Necessary :(b) On Steel Or Other Metal Surface :with Super Gloss (hi-gloss) -(iv) Two Coats (with Any Shade Except White)", "applying Interior Grade Acrylic Primer Of Approved Quality And Brand On Plastered Or Cencrete Surface Old Or New Surface To Receive Distemper/ Acrylic Emulsion Paint Including Scraping And Preparing The Surface Throughly, Complete As Per Manufacturer's Specification And As Per Direction Of The Eic. (in Ground Floor)(b) Two Coats(i) Water Based Interior Grade Acrylic Primer ", "applying Exterior Grade Acrylic Primer Of Approved Quality And Brand On Plastered Or Cencrete Surface Old Or New Surface To Receive Decorative Textured (matt Finish) Or Smooth Finish Acrylic Exterior Emulsion Paint Including Scraping And Preparing The Surface Throughly, Complete As Per Manufacturer's Specification And As Per Direction Of Theeic.in Ground Floor:(b) Two Coats", "applying Decorative Cement Based Paint Of Approved Quality After Preparing The Surface Including Scraping The Same Thoroughly (plastered Or Concrete Surface) As Per Manufacturer's Specification.in Ground Floor:(iii) Two Coats.", "supplying, Fitting And Fixing Cast Iron Heavy Type Spiral Staircase Of Approved Design With 50 Mm.dia. Stem And C.i. Steps 150 Mm As Per Design 900 Mm. High C.i, Railing Including Necessary M.s. Tie Of Suitable Section Embedded To Wall With Cement Concrete (1:2:4) Including Cost Of Intermediate C.i. Platform Secured With Necessary Tie To Stem And Wall With Cement Concrete (1:2:4) Including Fixing The Stem In Ground With Cement Concrete (1:3:6) Complete In All Respect With All Labour And Materials.(payment To Be Made On Vertical Height In Between 1st Step And Top Platform.)(b) With 900 Mm.dia. Well", "supplying And Laying True To Line And Level Vitrified Tiles Of Approved Brand (size Not Less Than 600 Mm X 600 Mm X 10 Mm Thick) In Floor, Skirting Etc. Set In 20 Mm Sand Cement Mortar (1:4) And 2 Mm Thick Cement Slurry Back Side Of Tiles Using Cement @ 2.91kg./sqm Or Using Polymerised Adhesive (6 Mm Thick Layer Applied Directly Over Finished Artificial Stone Floor/mosaic Etc Without Any Backing Course) Laid After Application Slurry Using 1.75 Kg Of Cement Per Sqm Below Mortar Only, Joints Grouted With Admixture Of White Cement And Colouring Pigment To Match With Colour Of Tiles / Epoxy Grout Materials Of Approved Make As Directed And Removal Of Wax Coating Of Top Surface Of Tiles With Warm Water And Polishing The Tiles Using Soft And Dry Cloth Upto Mirror Finish Complete Including The Cost Of Materials, Labour And All Other Incidental Charges Complete True To The Manufacturer's Specification And Direction Of Engineer-in-charge. (white Cement, Synthetic Adhesive And Grout Material To Be Supplied By The Contrr]e)i(i) With Application Slurry @1.75 Kg/ Sq.m, 20 Mm Sand Cement Mortar (1:4) & 2 Mm Thick Cement Slurry At Back Side Of Tiles, 0.2 Kg/ Sq.m White Cement For Joint Filling With Pigment.(a) Deep Colour & White", "supplying, Fitting & Fixing 1st Quality Ceramic Tiles In Walls And Floors To Match With The Existing Work & 4 Nos. Of Key Stones (10mm) Fixed With Araldite At The Back Of Each Tile & Finishing The Joints With White Cement Mixed With Colouring Oxide If Required To Match The Colour Of Tiles Including Roughening Of Concrete Surface, If Necessary Or By Synthetic Adhesive & Grout Materials Etc.(b) Wallwith Sand Cement Mortar (1:3) 15 Mm Thick & 2 Mm Thick Cement Slurry At Back Side Of Tiles Using Cement @ 2.91 Kg/sq.m & Joint Filling Using White Cement Slurry @ 0.20kg/sq.m.(a) Area Of Each Tile Upto 0.09 Sq.m(i) Coloured Decorative", "supplying And Laying Chequered Tiles Of Any Shade & Of Approved Quality With (1:1½:3) Cement Concrete Laid In Panels Or Patterns As Directed In Pavement, Footpath Etc. Including Necessary Underlay 25 Mm Thick [avg] Cement Mortar (1:3) Complete In All Respect With All Labour And Materials. [using Cement Slurry @ 4.4 Kg/sq.m At Back Side And @2.4 Kg/sq.m For Joint Filling]red Variety(ii) 30 Mm. Thick", "m.s. Structural Works In Roof Trusses With Tubular Sections Conforming To Is: 806-1968 & Is: 1161- 1998 Cnnected To One Another With Bracket, Gusset Cleats As Per Design, Direction Of Engineer-in-charge Complete Including Cutting To Requisite Size, Fabrication With Necessary Metal Arc Welding Conforming To Is: 816- 1969 & Is: 9595 Using Electrodes Of Approved Make And Brand Conforming To Is:814- 2004, Haulage, Hoisting And Erection All Complete.the Rate Includes The Cost Of Rolled Steel Section, Consumables Such As Electrodes, Gas And Hire Charge Of All Tools And Plants And Labour Reqired For The Work Including All Incidental Chages Such As Electricity Charges, Labour Insurance Charges Etc.payment To Be Made On The Basis Of Calculated Weight Of Structural Tubular Memebrs As Specified In Relevent Is Code In Finished Work.payment For Gusset, Bracket, Cleat May Be Made By Adding The Actual Weight Of Such Items With Weight Of Finished Structural Members. The Rates Are Considered For A Height Of Erection 8 M. / 2nd Floor Level From The Ground. Add 1.5 % Extra Over The Rate For Each Additional Floor Or 4m. Beyond The Initial 8 M. Or Part Thereof.i) For Trusses Spanning Up To 12.00 M", "supplying, Fitting & Fixing Zn-al Alloy (55% Al & 45% Zn) Coating Of 150 Grams Per Sq. Metre (followed By Colour Coated On Both Side) Steel Sheet Work Having Minimum Yield Strength Of 550 Mpa Of Trapizoidal Profile Of Approved Make (excluding The Supporting Frame Work) Fitted And Fixed With 55 Mm & 25 Mm Self Tapping Screw, Epdm Washer 16 Mm Dia & 3 Mm Th. Washer Etc. Complete With 150 Mm End Lap And One Corrugation Minimum Side Lap. (payment To Be Made On Area Of Finished Work).(i) In Roof:-a) With 0.5 Mm Thick Sheet", "galvanised Iron Sheet Eaves Gutter Fitted And Fixed With Necessary 50 Mm X 6 Mm M.s Flat Bar Clamps Bent To Design, Bolts, Nuts, Washers Etc. Complete. Eaves Gutter Made Of 0.63 Mm. Sheets.(300mm End Lapping)(a) 225 Mm. Wide Gutter", "wooden Eaves Board As Per Design, Fitted And Fixed Complete:in Ground Floor(iii) Ornamental Eaves Board (badam/gamar/champ/hallak)(a) 19mm Thick", "supplying, Fitting And Fixing Gunmetal Wheel Valve Of Approved Brand And Make Tested To 21 Kg Per Sq. Cm. (for Water Lines Only).(vii) 25 Mm Dia", "supplying, Fitting And Fixing Bib Cock Or Stop Cock.(b) (i) Chromium Plated Stop Cock (equivalent To Code No. 513(a) & 513(b) & Model - Tropical / Sumthing Special Of Essco Or Similar Brand).", "supply Of Upvc Pipes (b Type) & Fittings Conforming To Is 13592-1992(a) (i) Single Socketed 3 Meter Length(b) 110 Mm", "supply Of Upvc Pipes (b Type) & Fittings Conforming To Is 13592-1992(b) Fittings(ii) Plain Tee(b) 110 Mm", "supply Of Upvc Pipes (b Type) & Fittings Conforming To Is 13592-1992(b) Fittingsix) Bend 45º(b) 110 Mm", Supplying, Fitting And Fixing 10 Litre P.v.c. Low-down Cistern Conforming To I.s. Specification With P.v.c. Fittings Complete,c.i. Brackets Including Two Coats Of Painting To Bracket Etc., "supplying, Fitting And Fixing Shallow Water Closet Indian Pattern (i.p.w.c.) Of Approved Make In White Vitreous Chinaware In Position (excluding Cost Of Concrete For Fixing).(i) 580 Mm Long", "supplying P.v.c. Water Storage Tank Of Approved Quality With Closed Top With Lid (black) - Multilayer(a) 500 Litre Capacity", Supplying, Fitting And Fixing Best Quality Indian Make Mirror 5.5 Mm Thick With Silvering As Per I.s.i. Specifications Supported On Fibre Glass Frame Of Any Colour, Frame Size 550 Mm X 400 Mm, "supplying, Fitting And Fixing Cpvc (chlorinated Polyvinyl Chloride) Pipes Of Approved Make Conforming To Is-15778: 2007 . With All Necessary Accessories, Specials Viz. Socket, Bend, Tee, Union, Cross, Elbo, Nipple, Longscrew, Reducing Socket, Reducing Tee, Short Piece Etc. Fitted With Holder Bats Clamps, Including Cutting Pipes, Fitting, Fixing Etc. Complete In All Respect Including Cost Of All Necessary Fittings As Required,jointing Materials In Any Position Above Ground. (payment Will Be Made On The Centre Line Measurements Of Total Pipe Line Including All Specials. No Separate Payment Will Be Made For Accesories, Specials.(a) For Exposed Work(ii) Cpvc Pipes Class-2,sdr-13.5(dia)15 Mm", "supplying, Fitting And Fixing Cpvc (chlorinated Polyvinyl Chloride) Pipes Of Approved Make Conforming To Is-15778: 2007 . With All Necessary Accessories, Specials Viz. Socket, Bend, Tee, Union, Cross, Elbo, Nipple, Longscrew, Reducing Socket, Reducing Tee, Short Piece Etc. Fitted With Holder Bats Clamps, Including Cutting Pipes, Fitting, Fixing Etc. Complete In All Respect Including Cost Of All Necessary Fittings As Required,jointing Materials In Any Position Above Ground. (payment Will Be Made On The Centre Line Measurements Of Total Pipe Line Including All Specials. No Separate Payment Will Be Made For Accesories, Specials.(a) For Exposed Work(ii) Cpvc Pipes Class-2,sdr-13.5(dia)20 Mm", "wash Basin Vitreous China Of Approved Make (without Fittings) Supplied,fitted And Fixed In Position On 75mm X 75 Mm X 75 Mm Wood Blocks And C.i. Brackets Including Two Coats Of Painting Of C.i. Brackets.(i) 450 Mm X 300 Mm Size", "constructing Inspection Pit Of Inside Measurement 600mm 600mm X Upto 600mm (depth) With 250 Mm Thick 1st. Class Brick Work In Cement Mortar (1:4) On All Sides, Bottom Of The Pit Consisting Of 100 Mm Thick Cement Concrete (1:3:6) With Stone Chips Over A Layer Of Jhama Brick Flat Soling, 15 Mm Thick (1:4) Cement Plaster To Inside Walls And Out-side Walls Upto G.l. And 20 Mm.thick (1:4) Plaster To Bottom Of The Pit, Providing Necessary Invert With Cement Concrete (1:3:6) With Stone Chips As Per Direction, Neat Cement Finishing To Entire Internal Surfaces, Top Of The Pit Covered With 100 Mm Thick R.c.c. Slab (1:1.5:3) With Stone Chips And Necessary Reinforcements Upto 1% And Shuttering Including 6 Mm Thick Cement Plaster (1:4) In All External Surfaces Of The Slab And One 560 Mm Dia. R.c.c. Manhole Cover Of Approved Make Supplied, Fitted And Fixed In The Slab With Necessary Fittings, Necessary Earthwork In Excavation In All Sorts Of Soil, Filling Sides Of The Pit With Earth And Removing Spoils After Work Complete In All Respect With All Costs Of Labour And Materials.ii) With Bazree (n.b Variety) (other Than Sail/tata/rinl)", "supply Of Furnituresupply Of Revolving Chair.", Supply Of Office Table, Supply Of Office Chair, Supply Of Plastic Chair, Supplying, Fitting And Fixing Of Pvc Board Century Make., "internal Electrification For Wiring And Light Fittingdistribution Wiring In 2 X 22/0.3 (1.5 Sqmm) Single Core Stranded 'fr' Pvc Insulated & Unsheathed Copper Wire (brand Approved By Eic) In 20mm Size Pvc Rigid Conduit 'fr' (precision Make), With 1x22/0.3 (1.5 Sqmm) Single Core Stranded 'fr' Pvc Insulated & Unsheathed Copper Wire For Ecc, To Light/fan/call Bell Points With Modular Type Switch (brand Approved By Eic) Fixed On Modular Gi Switch Board With Top Cover Plate And 2 No. Suitable Size “ph & N” Copper Bar & Earthing Attachment Fixed On Wall Incl. Mending Good Damages To Original Finish.b) Average Run 6 Mtr", "distribution Wiring In 2 X 22/0.3 (1.5 Sqmm) Single Core Stranded 'fr' Pvc Insulated & Unsheathed Copper Wire (brand Approved By Eic) In 20mm Size Pvc Rigid Conduit 'fr' (precision Make), With 1x22/0.3 (1.5 Sqmm) Single Core Stranded 'fr' Pvc Insulated & Unsheathed Copper Wire For Ecc, To Light/fan/call Bell Points With Modular Type Switch (brand Approved By Eic) Fixed On Modular Gi Switch Board With Top Cover Plate And 2 No. Suitable Size “ph & N” Copper Bar & Earthing Attachment Fixed On Wall Incl. Mending Good Damages To Original Finish.c) Average Run 8 Mtr", "distribution Wiring In 1.1 Kv Grade 22/0.3 (1.5 Sqmm) Single Core Stranded 'fr' Pvc Insulated & Unsheathed Copper Wire (brand Approved By Eic) In 20mm Size Pvc Rigid Conduit 'fr' (precision Make), With 1.1 Kv Grade 1 X 22/0.3 (1.5 Sqmm) Single Core Stranded 'fr' Pvc Insulated & Unsheathed Copper Wire As Ecc, To 6a 3 Pin Modular Type Plug Socket & Switch (brand Approved By Eic) On 4 Module Gi Switch Board With 3/4 Module Top Cover Plate On Wall Incl. Necy. Connectionmaking Earthing Attachment, Painting And Mending Good Damages To Building Works.(a) On Board", "distribution Wiring In 1.1 Kv Grade 22/0.3 (1.5 Sqmm) Single Core Stranded 'fr' Pvc Insulated & Unsheathed Copper Wire (brand Approved By Eic) In 20mm Size Pvc Rigid Conduit 'fr' (precision Make), With 1.1 Kv Grade 1 X 22/0.3 (1.5 Sqmm) Single Core Stranded 'fr' Pvc Insulated & Unsheathed Copper Wire As Ecc, To 6a 3 Pin Modular Type Plug Socket & Switch (brand Approved By Eic) On 4 Module Gi Switch Board With 3/4 Module Top Cover Plate On Wall Incl. Necy. Connectionmaking Earthing Attachment, Painting And Mending Good Damages To Building Works.(d) Average Run 3 Mtr.", Supply & Fixing 240 V, 16 A, 3 Pin Modular Type Plug Socket (brand Approved By Eic) With 16a Modular Type Switch, Without Plug Top On 4 Module Gi Modular Type Switch Board With Top Cover Plate Flushed In Wall Incl. S&f Switch Board And Cover Plate And Making Necy. Connections With Pvc Cu Wire And Earth Continuity Wire Etc., "distribution Wiring In 1.1 Kv Single Core Stranded 'fr' Pvc Insulated & Unsheathed Copper Wire (brand Approved By Eic) In 20mm Size Pvc Rigid Conduit 'fr' (precision Make) Incl. Necy. Fittings As Required.(i) 2 X 22/0.3 (1.5 Sqmm) + 1 X 22/0.3 (1.5 Sqmm) Ecc", "distribution Wiring In 1.1 Kv Single Core Stranded 'fr' Pvc Insulated & Unsheathed Copper Wire (brand Approved By Eic) In 20mm Size Pvc Rigid Conduit 'fr' (precision Make) Incl. Necy. Fittings As Required.(ii) 2 X 36/0.3 (2.5 Sqmm) + 1 X 22/0.3 (1.5 Sqmm) Ecc", "distribution Wiring In 1.1 Kv Single Core Stranded 'fr' Pvc Insulated & Unsheathed Copper Wire (brand Approved By Eic) In 20mm Size Pvc Rigid Conduit 'fr' (precision Make) Incl. Necy. Fittings As Required.(iii) 2 X 56/0.3 (4 Sqmm) + 1 X 36/0.3 (2.5 Sqmm) Ecc", "supplying And Fixing Double-door Spn Mcb Distribution Board With Ip-42/43 Protection, Concealed In Wall After Cutting The Wall & Mending Good The Damages To Original Finish Incl. Inter Connection With Suitable Size Of Copper Wire And Neutral Link & Provision For Earthing Attachment.legrand Make 2+8 Way", "s & F 240/415 V Mcb Of Breaking Capacity 10ka & C Characteristics On Din Rail Of Existing Dbs And Necessary Connection.legrand Make 6-32a Sp", "s & F 240/415 V Mcb Of Breaking Capacity 10ka & C Characteristics On Din Rail Of Existing Dbs And Necessary Connection.legrand Make 40a Dp", Supply & Fixing Sheet Steel Main Switches On Angle Frame On Wall 32a 240v (havells Make), Fixing Only Single/twin Fluorescent Light Fitting Complete With All Accessories Directly On Wall/ceiling By Screws Etc., Supply & Fixing Angular Batten Holder (anchor) On 75mm Dia Pvc Round Block / Round Bakelite On Wall/ceiling., Fixing Only Floodlight Fittings On Top Of Masonary Structure By 3 Nos. 10 Mm Dia X 87 Mm Long Rag Bolts, Nuts & Double Washers Complete Either 37 Mm X 10 Mm Ms Flat Support/or By Other Means As Required, "fixing Exhaust Fan After Making Hole In Wall And Making Good Damages And Smooth Cement Finish Etc. As Practicable As Possible And Providing 2 * 1/1. 40 P.v.c. Insulated And Sheathed Wire And Making Connection For Exhaust Fan Of Dia:-b) 30 Cm . ( 12"" )", Fixing Only Cabin Fan On Wall/ceiling By S&f Rag Bolts, Nuts & Washers (6 Mm Dia X 62 Mm Long) Or As Reqd. Incl. S&f 24/0.20 Pvc Insulated Flexible Copper Wire 0.5 Mt. Length, "laying Of Cable As Below, After Cutting Floor/pavement/wall/ And Making Holes Incl., Embedding The Cable At An Average Depth As Below And Mending Good The Damages To Original Finish Incl. Removing The Rubbish.from 2.5 Sqmm To 35 Sqmm At An Average Depth Of 75 Mm Infloor/pavement/wall Etc.", Earthing With 50 Mm Dia Gi Pipe 3.64 Mm Thick X 3.04 Mts. Long And 1 X 4 Swg Gi (hot Dip) Wire (4 Mts. Long), 13 Mm Dia X 80 Mm Long Gi Bolts, Double Nuts, Double Washers Incl. S & F 15 Mm Dia Gi Pipe Protection (1 Mts. Long) To Be Filled With Bitumen Partly Under The Ground Level And Partly Above Ground Level Driven To An Average Depth Of 3.65 Mts. Below The Ground Level As Below: (a) By Isi-medium Gi Pipe, Connecting The Equipments To Earth Busbar Including Supplying And Fixing 20 Mm X 3 Mm Galvanised (hot Dip) Ms Flat On Walll/ Floor With Gi Saddles As Required And Connections To Equipments Incl. Drilling Holes, With Bolts, Nuts, Washers Etc., Supplying & Fixing 50mm Dia X 5.24 Metre Long (incl. Bends) Gi Pipe Vertical Type Service Bracket On Wall For Carrying 2 Wires And An Earth Wire Complete With Galv. Ms Clamps For Stay, Insulators And Earth Wire, 7/14 Swg Stranded Gi (hot Dip) Stay Wire With 230x31 Mm Dia Straining Screws, 75x88 Mm Porcelain Shackle Insulators With Galv. (hot Dip) Strips, Bolts, Bush Etc. Incl. Painting, Supply Only 20w Led Tube Light (make - Havells/philips), Supply Only 12w Led Bulb (make - Havells/philips), Supply Only 50w Led Street Light (make - Havells/philips), Supply Only Ventilating Fan (havells - Ventil Air Dx Hs White), Supply Only 300mm Wall Fan (havells Make - 450 Mm), Supply Only 2 Core 10 Sqmm Aluminium Unarmoured Cable, Add Gst @ 18%, Add Cess @ 1%